Better Light GEM-ACM1D Manual de usuario descargar pdf (Pagina 2)

2. Align the combination HW1490 Support Bars and

Burglary Module PCB with the holes located in HW1492

Right Side Plate and the HW1491 Left Side Plate. Se-

cure using four thumbscrews (item #4) and four external

tooth star washers (item #5).

3. Orient the Burglary Module above the motherboard

with its terminals towards the left side. On the right side

of the Burglary Module is a polarized 12 pin female rib-

bon connector "J2"; insert J2 into the male 12 pin con-

nector "J8" on the motherboard. Using the four 6-32

screws, mount the Burglary Module to the two HW1490

Support Bars (if not already pre-assembled).

TERMINAL DESCRIPTIONS

Maximum Burglary alarm and standby current can not ex-

ceed calculated maximum available Power Supply Cur-

rent or Available Battery Standby Current, whichever is

less. Typically, this is determined by the Available Bat-

tery Standby Current. Both must be calculated using de-

tailed spreadsheets to be created and provided for review

by the authority having jurisdiction.

Note: There are no integral burglary zones. Burglary

zones require either GEMC-EZM's wired to the Burg Bus,

SLC's connected to the motherboard, or a wireless re-

ceiver (GEMC-RECV) wired to the Fire bus (may be wired

to the Burg bus on a Burg-only system).

BELL ("Bell Output")

Terminal 1: Burg (+)

Terminal 2: Burg (–)

Supervised for open; use only one bell for proper super-

vision. Do not wire to Fire devices. Power limited out-

put.

AUX PWR

Terminal 3: Aux Power (+)

Terminal 4: Aux Power (–)

Separate Burglary Auxiliary Power for Burglary periph-

erals such as PIR's. Power limited output. Do not wire

to Fire devices.

PGM1, 2

Terminal 5, 6: PGM1 (–), PGM2 (–)

Programmable by zone, active low open collector out-

puts. Do not wire to Fire devices.

BURG BUS ("Remote Bus")

Terminal 7: Remote (+)

Terminal 8: Remote (–)

Terminal 9: Remote GRN

Terminal 10: Remote YEL

Do not wire to Fire devices.

Peripherals: GEMC-BK1 (at least one required),

GEMC-EZM, GEMC-OUT8, GEMC-RM3008, GEM-

ACM1D and GEMC-RECV. Separate Burglary Bus

supports all existing Gemini C-Series burglary peripher-

als and a maximum of 15 keypads (using separate

UL603 or UL1481 listed power supply, model GEMC-

12V2APS-CF or GEMC-12V2APS-R).

AUX RELAY

Terminal 11: COM

Terminal 12: N/C

Terminal 13: N/O

JP2 (Burg Service Jumper)

For Combination Fire and Burglary systems. When the

shunt is placed on the two left pins ("ON") of this three-pin

jumper, the system enters a special mode named "Burg

Service Mode" where the system stops processing Bur-

glary (non-Fire) alarm functions to permit the Burglary

part of the system to be serviced (changed) while allow-

ing the Fire system to continue to function as intended.

When servicing the Burglary system, we recommend en-

tering Burg Service Mode before removing power to avoid

the various troubles (such as a Burg keypad trouble) that

will occur. When Burg Service Mode is on, an LED lo-

cated just below the jumper will light. A Burg Service

Mode jumper is also located on the control panel mother-

board that is in parallel with the JP2 jumper on the

GEMC-BM/PS; either jumper can be used to initiate Burg

Service Mode, and the LED located just below the jumper

will light.

JP3 (No Time Out / 4.5 Hour Limit AC Fail Jumper)

The GEMC-BM draws all of its power from the control

panel motherboard. This three-pin jumper allows for the

selection of one of two options if the motherboard loses

AC power:

NO TIME OUT: Place the shunt on the two left pins (or

remove the shunt entirely) for power to be provided to

the GEMC-BM (and its connected devices) from the

motherboard until the battery power supplying the

motherboard is exhausted (and consequently both the

motherboard and the GEMC-BM Burglary module will

no longer be powered). The jumper is placed on these

two right pins ("NO TIME OUT") at the factory.

TIMED LIMIT AC FAIL: Not recommended to be en-

abled for Burglary Only systems. If the motherboard

loses AC power and the shunt is placed on the two right

pins, motherboard battery power will be provided to the

GEMC-BM (and its connected devices) for the pro-

grammed entry in the System Assignment screen

Time Selection tab, the Shed Burg on AC Fail field

(the number entered is x10 minutes). After the selected

time, power to the GEMC-BM will cease, thus conserv-

Item Part Number Description QTY

1 HW1688 Enclosure base 1

2 PCB Burg Burg PCB 1

3 HW1490 Support Bar 2

4 SC628 Thumbscrew 4

5 WA107

#6 External Tooth Star

Washer

6 SC270

Screw 6-32 x .25 with

washer (sems)

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Better Light GEM-ACM1D Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Cámaras Bridge Better Light GEM-ACM1D